Board logo

標題: WA M4精密管 [打印本頁]

作者: kwl    時間: 28-5-2008 00:01     標題: WA M4精密管

PDI 01 Inner Barrel for Western Arms M4A1 CQB-R (368mm)   usd$102.2

請問有冇師兄裝左? 想知裝左佢打topgas會變左咩力....

[ 本帖最後由 kwl 於 28-5-2008 02:07 編輯 ]
作者: maverick0    時間: 28-5-2008 09:27

A few comments:

1. It just appeared on the market on 26 or 27 May.
2. There are 3 lengths, from 210 mm  up
3. 6.01 barrels are tight. you have to select the appropriate bb or you'll jam the gun.
4. You may expect very strong power from a longer barrel.

[ 本帖最後由 maverick0 於 28-5-2008 09:51 編輯 ]
作者: 0050100    時間: 28-5-2008 10:08

志在分享.用條馬數管Cut350mm(ForM4-14.5"外管)再找師父攪重扺,
有錯請指教,別打頭.
作者: Pan    時間: 28-5-2008 10:11

引用:
原帖由 0050100 於 28-5-2008 10:08 發表
志在分享.用條馬數管Cut350mm(ForM4-14.5"外管)再找師父攪重扺,
有錯請指教,別打頭.
得就應該得既, 係煩少少 LO~同埋 d 數可以無咁準~
作者: 0050100    時間: 28-5-2008 12:30

係呀D數我段估的,圖只好作參考唔好照做呀,拿條原裝WA管去啦!
引用:
原帖由 kwl 於 28-5-2008 00:14 發表
PDI 01 Inner Barrel for Western Arms M4A1 CQB-R (368mm)   usd$102.2

請問有冇師兄裝左? 想知裝左佢打topgas會變左咩力....
我都想知下,6.01的威力.
不過我將條馬路二原裝管改左350mm長就已經邊入斜出.(強)
6.01唔知改SPR又有幾好玩呢?
作者: maverick0    時間: 28-5-2008 12:45

引用:
原帖由 0050100 於 28-5-2008 12:43 發表
係呀D數我段估的,圖只好作參考唔好照做呀,拿條原裝WA管去啦!



我都想知下,6.01的威力.
不過我將條馬路二原裝管改左350mm長就已經邊入斜出.(強)
6.01唔知改SPR又有幾好玩呢?
Must be FUN   Or else why WA would put such a short barrel inside CQBR to lower the power. It should be pretty accurate for a gas gun (I could get less than 1cm groups in 6m when I was testing various ways to fix/ stabilize the barrel). I guess it has great potential as an SPR.
作者: kwl    時間: 28-5-2008 16:36

引用:
原帖由 0050100 於 28-5-2008 12:43 發表
係呀D數我段估的,圖只好作參考唔好照做呀,拿條原裝WA管去啦!



我都想知下,6.01的威力.
不過我將條馬路二原裝管改左350mm長就已經邊入斜出.(強)
6.01唔知改SPR又有幾好玩呢?
368mm 6.01咪.........
作者: 車神勇    時間: 29-5-2008 00:01

引用:
原帖由 kwl 於 28-5-2008 16:49 發表



368mm 6.01咪.........
兩面石油氣罐!?!?




歡迎光臨 CGF (http://wargamehk.com/cgf/) Powered by Discuz! 6.0.0