CGF - Powered by Discuz! Board

標題: Need you input pls......... [打印本頁]

作者: siupo 時間: 23-2-2010 23:34 標題: Need you input pls.........

I finally got my SCK Max before the CNY and I have to say what a wonderful gun it is.... After playing with it for a while, I now have some questions that need you experts to help me out:

- can someone teach me what is the most effective way to load BBs to systema magazines? I saw someone from youtube who uses an metal adaptor along with a regular BB loader to get BBs in.  Is there any shop or person that I can get this adaptor from?  using the long tube and red plastic just isn't a practical on the field.

- will mil/spec CTR be directly installed to the buffer tube of PTWs?

- can PTS UBR be installed to the lower receive of PTW?  I know there will be modification work involved but I might not want to take the risk if mil/spec UBR is the only way but case getting one to HK isn't exactly cheap.

- can anyone let me know where can I get the Pin Punch for putting in or getting in the pins?  I used some generic tools but I figure getting a set of those pin punch would be the best way to deal with the gun in the future.

Your input would be greatly appreciated!!!

作者: red_ant_tony 時間: 23-2-2010 23:55

1) I found that using the regular BB loader (without adapter) is probably the fastest way. With some training it can be done. Personally I would grab the mag using my left hand and position my left index finger horizontally just in front of the lip to prevent the nozzel of the loader from slipping in front. Then load the BBs in with the loader vertically.
2) Should be OK. (someone correct me if I'm wrong)
3) Han't tried it before. Should be OK.
4) I have been trying to get a set of tools myself. But it's not easy. I've seen QxF having a complete set for sale - real gunsmith tools. You can get one or two sizes from Ap Liu Street but never the complete range that you need. My cheaper solution was to get a set of $10 screw drivers set and cut the ends with a metallic cutter, pollish the rough ends a bit and ended up with a nice functional range of puches.

Hope that helps

作者: jpg 時間: 24-2-2010 03:16 標題: 回覆 1# 的帖子

2) Mil spec CTR may fit or may not fit. But PTW stock tube is between mil spec and commerial size. Commerical guarantee will work, but might be a little bit wobble. So I think the best way is use mil-spec CTR and sand down the inside a little bit in order to get a tight fit on your buffer tube.
3) UBR PTS aeg version will not fit. Gbb version, may be.

作者: sailun412 時間: 26-2-2010 01:05

- No CTR can directly fit on the PTWs original buffer tube without mod except the comm'l spec.

作者: jpg 時間: 26-2-2010 03:09 標題: 回覆 4# 的帖子

That's what I think, but I am so surprise my ACS Mil spec can fit on directly, even though it's a little bit tight. On the other hand, my CTR Mil spec can't fit on directly. QC problem??

作者: 小安哥 時間: 26-2-2010 04:15

引用:

原帖由 jpg 於 26-2-2010 03:09 發表
That's what I think, but I am so surprise my ACS Mil spec can fit on directly, even though it's a little bit tight. On the other hand, my CTR Mil spec can't fit on directly. QC problem?? .

Is that ACS PTS version, if yes, then i may go for it

thanks.

作者: jpg 時間: 26-2-2010 16:41 標題: 回覆 6# 的帖子

No, RS ACS mil-spec version. To be honest, I will still go with mil-spec no matter what, since commerical is too loose for PTW buffer tube. It won't give you a tight fit, and the stock will wobble.

作者: 小安哥 時間: 27-2-2010 00:11

引用:

原帖由 jpg 於 26-2-2010 16:41 發表
No, RS ACS mil-spec version. To be honest, I will still go with mil-spec no matter what, since commerical is too loose for PTW buffer tube. It won't give you a tight fit, and the stock will wobble.

thanks

作者: siupo 時間: 27-2-2010 22:39

thanks for all the useful feedbacks!

作者: 小安哥 時間: 28-2-2010 19:11

Oh sorry, i want to ask which brand's tangodown grip is better? thnks.

作者: sailun412 時間: 28-2-2010 20:10

- Tango down mod is the best for sure!
- G&x airsoft version is the 2nd choice for me...

歡迎光臨 CGF (http://wargamehk.com/cgf/)