CGF - Powered by Discuz! Board

標題: PGC 第一水的 P226 Non-Rail (Not navy)下身可否裝Hogue Rubber Grip [打印本頁]

作者: ParcoNg 時間: 6-6-2011 15:10 標題: PGC 第一水的 P226 Non-Rail (Not navy)下身可否裝Hogue Rubber Grip

As the tittle.
If not, is it possible to modify the pistol in order to fit the grip?
And how much I have to paid to do this modification?
Thanks a lot.

[ 本帖最後由 ParcoNg 於 6-6-2011 16:35 編輯 ]

作者: Riderkuuga 時間: 6-6-2011 16:59

PGC下身可裝任何真品Grip的, ching

作者: ParcoNg 時間: 6-6-2011 17:37

Thanks for your reply.
But I heard of that the first version of PGC kit can't fit the real grip.
So that PGC produce the second version of those kits which can use the real hand grip.

作者: Riderkuuga 時間: 7-6-2011 16:01

Sorry for never heard any different of first / second version.....

Maybe other ching can help??

作者: geoprotex 時間: 7-6-2011 16:10

As per my knowledge, there is only one version of PGC P226 non-rail frame.
Would you mind to upload some pictures of your 1st gen frame so we could have a comparison?

作者: ParcoNg 時間: 7-6-2011 17:27

I'm don't have the p226 yet. I just planning to buy one.
But I found these two link on the internet.
"1st generation" : http://www.wgcshop.com/wgc2008/m ... amp;catid=&cat=
2nd generation" :http://www.wgcshop.com/wgc2008/m ... amp;catid=&cat=
Please look at the product information. The"1st generation' kit doesn't say that it can install the real hand gun grip.
Thanks for your help.

作者: geoprotex 時間: 7-6-2011 17:33

So why don't you choose the 2nd gen?

作者: ParcoNg 時間: 7-6-2011 17:49

I'm planning to buy a second hand pistol on the market.
But I can only find the P226 with first gen. PGC kit.
So that I wanna know is it possible to install the grip on the first gen. frame.

作者: Riderkuuga 時間: 9-6-2011 15:44

引用:

原帖由 ParcoNg 於 7-6-2011 17:27 發表
I'm don't have the p226 yet. I just planning to buy one.
But I found these two link on the internet.
"1st generation" : http://www.wgcshop.com/wgc2008/m ... rch_From=searchItem ...

After compared with the two links, yes, you should buy the 2 gen for install the real grip.

I think you still can find it at gun street, please try.

作者: mk23 時間: 9-6-2011 17:29

最早早的第一期PGC 226金身只能裝回Marui grip,其它真品裝唔到(那應該同Prime同期).
到之後的如有Blackwater版的那些先能裝到.

作者: lamlok 時間: 11-6-2011 00:26

i can confirm that the 1st gen version cannot use real grip, coz i have one. the 1st gen is completely the same as marui frame, using original hammer spring housing, which is too wide for real grip.
2nd gen feature integrated hammer spring housing, like a real gun, so it can use real grip.

歡迎光臨 CGF (http://wargamehk.com/cgf/)