CGF - Powered by Discuz! Board

標題: casv installation help [打印本頁]

作者: daiski 時間: 22-6-2007 08:40 標題: casv installation help

Hi brothers, need you advice on this. I got this casv and when I want to install the bottom part of the handguard, it won't go in because the the part I'm pointing out is 1mm too wide. Should I use a file to file it down? But I'll kill the paint job if I do. What other method do you recommend? Any brother has this problem with CASV?
Thanks

作者: Pan 時間: 22-6-2007 11:49

咩牌架???

作者: devil-sniper 時間: 22-6-2007 11:51

引用:

原帖由 Pan 於 2007-6-22 11:49 發表
咩牌架???

Vltor.....................?

作者: daiski 時間: 22-6-2007 12:00

I give up. I realize filing down won't help because the it's at least 2mm out of place. I try to remove part 1 to see if the casv will budge. However it's so tough to remove the front sight.

作者: Pan 時間: 22-6-2007 12:00

引用:

原帖由 devil-sniper 於 22-6-2007 11:51 發表

Vltor.....................?

但係無奶油 vltor 都會咁 bo

作者: Pan 時間: 22-6-2007 12:01

引用:

原帖由 daiski 於 22-6-2007 12:00 發表
I give up. I realize filing down won't help because the it's at least 2mm out of place. I try to remove part 1 to see if the casv will budge. However it's so tough to remove the front sight.

會唔會真係頂住左呢??
因為我裝果時無裝到果 part1 的~

作者: daiski 時間: 22-6-2007 12:01

no la it's copy

作者: daiski 時間: 22-6-2007 12:02 標題: 回覆 #6 Pan 的帖子

that's what I'm trying to remove. but the front sight won't come out. do i need sight removal tool to remove a gp front sight?? :x :x

作者: Pan 時間: 22-6-2007 12:04

引用:

原帖由 daiski 於 22-6-2007 12:02 發表
that's what I'm trying to remove. but the front sight won't come out. do i need sight removal tool to remove a gp front sight?? :x :x

鎚仔打一枝幼既螺絲批

作者: daiski 時間: 22-6-2007 12:18

引用:

原帖由 Pan 於 22-6-2007 12:04 發表

鎚仔打一枝幼既螺絲批

I've already removed the 2 pins, but the sight is so tight.

作者: Pan 時間: 22-6-2007 12:18

引用:

原帖由 daiski 於 22-6-2007 12:18 發表

I've already removed the 2 pins, but the sight is so tight.

仲有粒機米呢

係個底度

作者: daiski 時間: 22-6-2007 12:26

引用:

原帖由 Pan 於 22-6-2007 12:18 發表

仲有粒機米呢
係個底度

oops...how do you take that out????

作者: daiski 時間: 22-6-2007 12:32

never mind. i'll use an allan wrench hehe

作者: devil-sniper 時間: 22-6-2007 12:36

引用:

原帖由 Pan 於 2007-6-22 12:00 發表

但係無奶油 vltor 都會咁 bo

o甘無o野o拉.............

作者: whisky 時間: 22-6-2007 12:37 標題: 回覆 #12 daiski 的帖子

三角星底部，有個細細個既咚，開支電筒照入去，你會發覺裡面有粒六角形既野，個粒野就係叫機米，用六角匙樓粒機米出泥

作者: Pan 時間: 22-6-2007 12:48

引用:

原帖由 daiski 於 22-6-2007 12:26 發表

oops...how do you take that out????

六角匙...
得閒去買返一set 對將來整槍好有用的

作者: daiski 時間: 22-6-2007 12:57

hey Pan, thanks for your help. finally got it done

作者: daiski 時間: 22-6-2007 13:00

引用:

原帖由 whisky 於 22-6-2007 12:37 發表
三角星底部，有個細細個既咚，開支電筒照入去，你會發覺裡面有粒六角形既野，個粒野就係叫機米，用六角匙樓粒機米出泥

haha, it was so small i didn't know it was a 六角. I took it out with an allen key lu

作者: Pan 時間: 22-6-2007 13:06

引用:

原帖由 daiski 於 22-6-2007 12:57 發表
hey Pan, thanks for your help. finally got it done

合得埋就得了
舉手之勞姐

對你把槍有少少提意~~~~
如果用 casv 既~~~就試下用 ARMS 既 #40 or GG&G 隻 BUIS 呢~~
同埋個 wilcox aimpointy mount 唔似太襯 CASV

作者: Pan 時間: 22-6-2007 13:08

my one~~

作者: daiski 時間: 22-6-2007 13:11

引用:

原帖由 Pan 於 22-6-2007 13:06 發表

合得埋就得了
舉手之勞姐

對你把槍有少少提意~~~~
如果用 casv 既~~~就試下用 ARMS 既 #40 or GG&G 隻 BUIS 呢~~
同埋個 wilcox aimpointy mount 唔似太襯 CASV

i'm very poor ga. i need to buy accessory bit by bit. i got the wilcox mount originally to go with the mk18 look.

作者: Pan 時間: 22-6-2007 13:13

引用:

原帖由 daiski 於 22-6-2007 13:11 發表

i'm very poor ga. i need to buy accessory bit by bit. i got the wilcox mount originally to go with the mk18 look.

慢慢執

歡迎光臨 CGF (http://wargamehk.com/cgf/)