CGF - Powered by Discuz! Board

標題: gp urx middle [打印本頁]

作者: fusionjc 時間: 18-9-2011 14:45 標題: gp urx middle

The real rail is a fantasy for me, when I knew the toy rail announed from gp on Aug. Fine, I give up .
Any c-hing have bought this Toy rail before? Is it fit for ptw? I will go to buy it this week if no adverse comment here XD thzthz

作者: Elf 時間: 18-9-2011 16:45

would like to hear some feedback from you if you do get it

作者: terrylui 時間: 18-9-2011 20:46

The urx of gp barrel nut is only fit for toy gun mechanism only
If you wanna get one for saving money, you need to do some modification in either urx nut or ptw upper receiver because the ptw barrel nut is little bit bigger than toy gun nut.
Your choice....

作者: ayaka 時間: 18-9-2011 20:57

check out my old photos in the PTW美砂酮中心 (P.3)
GP barrel nut spec.(Marui toy spec.) is larger than the PTW/RS receiver spec.
so gp urx barrel nut will fit ptw upper well.
Hope it helps

作者: fusionjc 時間: 18-9-2011 21:48 標題: 回覆 4# 的帖子

Wow nice gun brother! Actualy I would like to know did you do any modification for the gp barrel nut when you install it? Any corresponding work/parts I need to prepare? Is it easy to install? And the one thing come to my attention that I cant find the gas block on your gun, where is it XD?

[ 本帖最後由 fusionjc 於 18-9-2011 21:49 編輯 ]

作者: terrylui 時間: 18-9-2011 22:21

引用:

原帖由 ayaka 於 18-9-2011 20:57 發表
check out my old photos in the PTW美砂酮中心 (P.3)
GP barrel nut spec.(Marui toy spec.) is larger than the PTW/RS receiver spec.
so gp urx barrel nut will fit ptw upper well.
Hope it helps

ht ...

So one more hand guard can directly go with PTW, were I correct? Where is my note book~~? Mark it down!!!
If yes, you bring a nice gift to ptw players, thx bro~

Anyway, nice gun!

[ 本帖最後由 terrylui 於 19-9-2011 19:29 編輯 ]

作者: ayaka 時間: 19-9-2011 01:33 標題: 回覆 5# 的帖子

No mod. is needed!!
but you need a GP urx installation tool.

I used 7" gas tube and blocks inside the URX.

作者: fusionjc 時間: 19-9-2011 09:15

Can I install it without GP urx inst tool.... you know it is fucking expensive and not desirable....

作者: ayaka 時間: 19-9-2011 11:54 標題: 回覆 8# 的帖子

yes, you can
but i don't think it is secure...

作者: seals9121 時間: 19-9-2011 14:32

引用:

原帖由 ayaka 於 18-9-2011 20:57 發表
check out my old photos in the PTW美砂酮中心 (P.3)
GP barrel nut spec.(Marui toy spec.) is larger than the PTW/RS receiver spec.
so gp urx barrel nut will fit ptw upper well.
Hope it helps

ht ...

nice looking gun, bro

作者: spec.ops. 時間: 20-9-2011 01:10

引用:

原帖由 seals9121 於 19-9-2011 14:32 發表

nice looking gun, bro

咁呢枝呢?

圖片附件: 20110920083.jpg (20-9-2011 01:10, 142.45 KB) / 該附件被下載次數 223
http://wargamehk.com/cgf/attachment.php?aid=145633

歡迎光臨 CGF (http://wargamehk.com/cgf/)