CGF - Powered by Discuz! Board

標題: Polymer (PLASTIC) Gun 一齊so吓d膠槍! [打印本頁]

作者: gykl3344 時間: 13-10-2011 05:21 標題: Polymer (PLASTIC) Gun 一齊so吓d膠槍!

Let's show some gun made of Polymer Frame!
我喜歡叫佢做膠槍

無什特別,GLOCK GEN3 22 一把.加個爛鬼MAG WELL.
本來想買17,唸著9MM子彈平(CAD10/~HK$80,50粒FMJ).點知買個時17鬼咁缼貨,買咗22後週街都係x!!

[ 本帖最後由 gykl3344 於 13-10-2011 05:33 編輯 ]

作者: 5sfll970 時間: 13-10-2011 09:42

Nice glock...
其實可唔可以買個17 slide連barrel換上去, 就變到可以打9mm?

作者: gykl3344 時間: 13-10-2011 09:59 標題: 回覆 2# 的帖子

唔洗, 有d 專比 glock 22 用的 9mm barrel (LONE WOLF BARREL). 唔洗換slide. 不過我唔多仲意 (仲有glock 17/ 22 轉.22lr 的 kit).不過要用9mm mag.

[ 本帖最後由 gykl3344 於 13-10-2011 10:02 編輯 ]

作者: 5sfll970 時間: 13-10-2011 11:33

引用:

原帖由 gykl3344 於 13-10-2011 09:59 發表
唔洗, 有d 專比 glock 22 用的 9mm barrel (LONE WOLF BARREL). 唔洗換slide. 不過我唔多仲意 (仲有glock 17/ 22 轉.22lr 的 kit).不過要用9mm mag.

So 只換管同匣only...好方便. 又平.
其實用呢個方法一雞幾味都唔錯.
不過如果中意個型號就無辦法喇. 17就係17.

話時話, slide就有mark glock22.
不過frame就無喇...係唔係架?
定係下身都有model marking?

作者: b9296 時間: 14-10-2011 00:40 標題: 回覆 1# 的帖子

咦 - 個下身右邊上面個marking有啲怪：但又影得唔太清楚...

作者: rho837 時間: 14-10-2011 02:01

你係咪講個條Pin? ‧40係多左條pin.

作者: noveske 時間: 14-10-2011 08:10

What brand is that magwell?

作者: gykl3344 時間: 14-10-2011 09:19 標題: 回覆 5

If you mean that little silver pin, that's the serial number.
Gen3 has serial number on slide, barrel & frame.
Model number only on slide.
Sorry, I need to check who makes the well.

作者: gtoray 時間: 14-10-2011 09:25

感謝 gykl3344 兄分享
看來真鐵比 airsoft 更似玩具

作者: gykl3344 時間: 15-10-2011 04:57 標題: 回覆 9# 的帖子

似唔似就好難說,不過有好多真槍的finish 就比airsoft粗糙

作者: gtoray 時間: 15-10-2011 05:10

引用:

原帖由 gykl3344 於 15-10-2011 04:57 發表
似唔似就好難說,不過有好多真槍的finish 就比airsoft粗糙

如果 airsoft 個 slide 出呢個 finishing
玩家就一定唔收貨

作者: b9296 時間: 15-10-2011 12:44

引用:

原帖由 gykl3344 於 14-10-2011 09:19 發表
If you mean that little silver pin, that's the serial number.
Gen3 has serial number on slide, barrel & frame.
Model number only on slide.
Sorry, I need to check who makes the well.

唔係 - 應該簡單啲講係平時刻住Made In Austria嗰個位...您嗰支個marking又唔似真又唔似假

...

作者: gykl3344 時間: 16-10-2011 09:55

小弟唔係GLOCK專家,不過呢個問題都好多人問過.
加拿大同美國依家大多數都唔mark "Made in Austria", 係, marks "GLOCK INC, Smyrna, GA" ，　即Glock USA, 不過SLIDE上依然mark 著"AUSTRIA".唔清楚幾時開始,GEN3開始?我都唔清楚.有可能個FRAME係GLOCK USA　造.
話時話ＧＬＯＣＫ　在香港都有弋公司，信德中心３１０２．唔知有無ＧＬＯＣＫ　賣
"MADE IN JAPAN, TANAKA"當然係AIRSOFT LA.

[ 本帖最後由 gykl3344 於 16-10-2011 10:03 編輯 ]

作者: b9296 時間: 17-10-2011 00:37

引用:

原帖由 gykl3344 於 16-10-2011 09:55 發表
小弟唔係GLOCK專家,不過呢個問題都好多人問過.
加拿大同美國依家大多數都唔mark "Made in Austria", 係, marks "GLOCK INC, Smyrna, GA" ，　即Glock USA, 不過SLIDE上依然mark 著"AUSTRIA".唔清楚幾時開始,GEN3開始 ...

未必 - Springfield支XD個下身係Croatia造...可能Glock都已經將啲下身outsource到唔知邊度生産...

可以系商業大廈買鎗 - 我都想

（wholesale落單可能得 - retail今時今日要去鎗鋪）

我下面嗰支係cap鎗（SPG）...未摸過美國版既Glock所以唔知質感上有無分別...

作者: gykl3344 時間: 17-10-2011 05:55 標題: 回覆 7

smartlock.com

作者: gykl3344 時間: 17-10-2011 06:09 標題: 回覆 14

You know what. A lots of newer airsoft guns feel very close to real steel.
I have handled RS AK47, ICS M4/ M16 series, ICS SG551 etc.
This also include ARES Tavor. Even this made of “Plastic", and there is some cosmetic difference including surface texturewise, but still feel pretty solid.
Much Much better than my TM M16A2. So even I can own real steel, I am willing to collect this kind of airsoft

作者: 5sfll970 時間: 17-10-2011 20:51

引用:

原帖由 gykl3344 於 17-10-2011 06:09 發表
You know what. A lots of newer airsoft guns feel very close to real steel.
I have handled RS AK47, ICS M4/ M16 series, ICS SG551 etc.
This also include ARES Tavor. Even this made of “Plastic", and ...

That is because RS is a real steel factory...it is like the toy division of Norinco.

作者: garand 時間: 15-11-2011 22:15 標題: 回覆 16# 的帖子

don't forget plastic rifle AUG!

歡迎光臨 CGF (http://wargamehk.com/cgf/)