d.s

引用:

原帖由 abadname 於 23-1-2009 23:04 發表
您好：我看了一下PRIME的金身，您說的圖釘是把GAS TUBE那個孔給塞住的嘛？
我以為是不需要的，因為PRIME的拉柄已經做得比較長，剛好是貼到GAS TUBE那個孔...
而WA原廠的拉柄比較短，所以需要哪個圖釘來補滿那個空隙 ...

剛好要替友人安裝Prime的金身,不麻煩~不麻煩~
其實這圖釘是必須品,請看圖吧~!

gabrielwong1991

Just one more question before coming back HK and buy the G&P M4A1 Full Kit.

I bought a DD MK18 RISII, Magpul CTR non-mil spec and Magpul MIAD

will the G&P M4 fits all three things above? will there be any "gap" between it?

I wish i can get the G&P M4 GBB but if the three things doesn't fit into it then i think i need to stick to WE m4 la.....

d.s

引用:

原帖由 gabrielwong1991 於 24-1-2009 00:30 發表
Just one more question before coming back HK and buy the G&P M4A1 Full Kit.

I bought a DD MK18 RISII, Magpul CTR non-mil spec and Magpul MIAD

will the G&P M4 fits all three things above? will th ...

Magpul CTR non-mil spec and Magpul MIAD Can fit G&P M4A1 Full Kit,
DD MK18 RISII你會買真品 or Copy?

gabrielwong1991

i bought it through a company that ships to UK for Magpul Product not PTS
I bought the DD MK18 copy but real steel spec.
I was just wondering because non-mil spec is bigger than mil spec.

Cheers mate btw =]

[ 本帖最後由 gabrielwong1991 於 24-1-2009 04:07 編輯 ]

d.s

引用:

原帖由 gabrielwong1991 於 24-1-2009 04:06 發表
i bought it through a company that ships to UK for Magpul Product not PTS
I bought the DD MK18 copy but real steel spec.
I was just wondering because non-mil spec is bigger than mil spec.

Cheers  ...

Magpul MIAD 暫時只有真品可裝,亦對應GP金屬身,而PTS只有for AEG的.
而CTR,我的是最早期未印有PTS Marking的PTS版,裝在GP Buffer Tube上很fit.non-mil spec我就搞不清楚了..
DD MK18 copy你買GP的就能對應.

lololo

請問有邊隻low profile gas block對應原裝WA M4 carbine 回氣管及外管呢??
Thanks

[ 本帖最後由 lololo 於 24-1-2009 11:36 編輯 ]

d.s

引用:

原帖由 lololo 於 24-1-2009 11:34 發表
請問有邊隻low profile gas block對應原裝WA M4 carbine 回氣管及外管呢??
Thanks

對應原裝WA M4 carbine 回氣管的話係冇,皆因WA 回氣管較粗,入唔到.
只計外管就應該市面有售嘅low profile gas block都得,
個人建議:low profile gas block最好揀隻輕身d

lololo

引用:

原帖由 d.s 於 24-1-2009 11:48 發表

對應原裝WA M4 carbine 回氣管的話係冇,皆因WA 回氣管較粗,入唔到.
只計外管就應該市面有售嘅low profile gas block都得,
個人建議:low profile gas block最好揀隻輕身d

Thanks~~
其實宜家D GP WA M4隻匣係咪同原裝WA一樣?
定以改GP料??O-ring? Hammer Lock?

d.s

引用:

原帖由 lololo 於 24-1-2009 13:02 發表


Thanks~~
其實宜家D GP WA M4隻匣係咪同原裝WA一樣?
定以改GP料??O-ring? Hammer Lock?

匣同原裝WA一樣,邊有咁荀?
GP想做WA都唔肯啦~

abadname

看到您提供的圖，我終於了解了...
不知道是不是錯覺，總覺得您圖上金身間隙（拉柄與金身之間）似乎比較大，我大約量了一下我的情形約0.5mm...
不知是否PRIME有小改款呢？

gabrielwong1991

i c thats great!

Much appreciated !

Thanks!

How many mag do you own?

d.s

引用:

原帖由 gabrielwong1991 於 24-1-2009 19:31 發表
i c thats great!

Much appreciated !

Thanks!

How many mag do you own?

only1

[ 本帖最後由 d.s 於 24-1-2009 21:21 編輯 ]

桸藍

今日換value lock時整斷咗個匣低的耳仔,
因為條彈弓點都放得唔好,現在剛剛ok,
請問對個匣有影響嗎?
另外有什麼方法較易放回條彈弓加頂彈的膠?
thx~

lololo

引用:

原帖由 桸藍 於 24-1-2009 22:01 發表
今日換value lock時整斷咗個匣低的耳仔,
因為條彈弓點都放得唔好,現在剛剛ok,
請問對個匣有影響嗎?
另外有什麼方法較易放回條彈弓加頂彈的膠?
thx~

我都一早整斷咗,除左外觀,應該影響不大..
請問ching換哪家既value lock 呢??

d.s

My MAG

Total跌過5次~!!不過冇一次係我自已跌,全部都係借人玩時跌~~
雖然跌到個低爛哂,但表現都仲好好

[ 本帖最後由 d.s 於 25-1-2009 00:25 編輯 ]