18 12
發新話題
打印

TLP 15 Fuzzy Logic Charger 220 V 一問 萬分感激各位的幫忙

TLP 15 Fuzzy Logic Charger 220 V 一問 萬分感激各位的幫忙


TLP 15 Fuzzy Logic Charger 220 V


想請問各位, 這一部叉機好嗎 ?


我現在用緊一TLP 4000C Battery Charger,


但我成日唔清楚佢幾時 charge 完 `


不停 Beep 足一晚甚至兩晚 tim ...


我要幫朋友買部, 但又怕 advice 部唔好野給他, plz help ... thank you `


另外 APEZ charger 又好嗎 ?


Thank you very much much much much much again `


萬分感激各位的幫忙 ~!!!!!!!!





附件

TLP 15.jpg (20.3 KB)

7-2-2009 12:12

我想買的

TLP 15.jpg

TLP 4000C.JPG (34.72 KB)

7-2-2009 12:12

現在用的

TLP 4000C.JPG

TOP

師兄,我個部都係,
差一陣就bit,但用電時先發覺未差完
好在自己有spare電
Ken's Custom Magpul M4  

TOP

nonono, the shop keep told me that, it will keep on beeping, but until it finished, it will stop ...

But i dont think i have ever seen it stops beeping ...

and i have already lost three 8.4 V Intellect batteries on the 4000C already ...

Three of them both burnt down ...

TOP

一路差一路bit.....
唔會呀...你係咪唔會咗
Ken's Custom Magpul M4  

TOP

4000c 慢charge係會keep住beep架喎
我用8.4v大電的方法係:
先放電 (雖然唔知舊電放左幾耐)
再快charge (個掣大約扭3/4)
滿左再放電
然後再charge

你會發現充電時間明顯係長過第一round叉的
如果呢個過程都仲係半個鐘左右完成,咁我會再放多次電再叉

叉的時候留意電的溫度,放佢去個散熱好的地方

TOP

引用:
原帖由 louisli 於 7-2-2009 13:56 發表
4000c 慢charge係會keep住beep架喎
我用8.4v大電的方法係:
先放電 (雖然唔知舊電放左幾耐)
再快charge (個掣大約扭3/4)
滿左再放電
然後再charge

你會發現充電時間明顯係長過第一round叉的
如果呢個過程都 ...
如果charge 8.4v 細電 , 要幾多A 同太約幾耐左右

勞煩師兄指教

TOP

For You Guys Reference:

TOP

回復 7# 的帖子


Well really thanks a lot   啊強   ~!

But this list is fit for the model 4000c, all charger, rite ? It will be a great help for u if i can have a list like that ~ Thanks a lot man ~~~!!!


Thanks louisli  too ~

But fast charge for how long will means it finished ? Is it wait for it to switich to slow charge ? thank you ~

And is it the mAh needs to fit for specific batteries ?

like my Intellect 8.4 V 1400 mAh small battery, switch the circle button to 1400 mAh, then charge it for 1 hr ?

And weeks ago, i went to gun street to buy battery AGAIN in "戰死" the shop keeper told me that this kinds of battery shouldn't discharge, they have no memory effect `

But for my limited knowledge, I am not sure ... I am confused ... sorry for my foolish ...

Plz help ... Thank you ` MUCHMUCHMUCH ~!




[ 本帖最後由 kelvinngrub 於 7-2-2009 20:12 編輯 ]

TOP

引用:
原帖由 kelvinngrub 於 7-2-2009 20:10 發表

Well really thanks a lot   啊強   ~!

But this list is fit for the model 4000c, all charger, rite ? It will be a great help for u if i can have a list like that ~ Thanks a lot man ~~~!!!


Than ...
NI-MH毋需放電
不過i記細電...good luck


btw, 我用4000c, 對付個慢叉係咁咇嘅方法係.........









































拆左個buzzer去

TOP

我都有隻TLP EXPRO 叉機, 用Intellect 9.6V 2000mAh
鋪頭教我用1A- 2A, 快叉, 我就用1A 黎叉, 請問o岩唔o岩呢

唔該

TOP

引用:
原帖由 vassilihk 於 7-2-2009 18:22 發表


如果charge 8.4v 細電 , 要幾多A 同太約幾耐左右

勞煩師兄指教
無試過慢叉,頂唔住佢d bb 聲

TOP

引用:
原帖由 zeta 於 9-2-2009 18:59 發表

NI-MH毋需放電
不過i記細電...good luck


btw, 我用4000c, 對付個慢叉係咁咇嘅方法係.........






拆左個buzzer去8 ...
有師兄試過換做LED
有心機d的可以整個switch,鐘意led就led,b就b

TOP

引用:
原帖由 kelvinngrub 於 7-2-2009 20:10 發表

Well really thanks a lot   啊強   ~!

But this list is fit for the model 4000c, all charger, rite ? It will be a great help for u if i can have a list like that ~ Thanks a lot man ~~~!!!


Than ...
快轉慢就代表充電完成架啦
通常叉完之後會等佢慢叉一個鐘左右

TOP

我差都係用快差,唔怪得唔bit
Ken's Custom Magpul M4  

TOP

引用:
原帖由 louisli 於 10-2-2009 12:54 發表

無試過慢叉,頂唔住佢d bb 聲
so far 我用4000c 的情況係

快叉i記 8.4v 細電 , 擺低左一個月 , 用1.5a 叉 , 叉左幾粒鐘先cut 先轉慢叉...

所以我為免打game 時無電 , 再叉多一次 , 但o個次又差唔多 1-2個鐘搞掂 , 同樓上個chart 一樣

搞到我都唔知舊電死左定係個叉機short short 地

TOP

 18 12
發新話題