fwkwong

9" Troy TRX Extreme with CQBR lenght

fwkwong

Very easy !! This is a real steel, come with a very good Troy trench to tight up the special barrel nut.  The barrel nut looks similar to the original delta ring but with sharper teeth.  Then the rail is designed to be push into this  (like Noveske) nut with the top rail at 11 o'clock.  Afterwards, just twist it to 12 o'clock and the top rail will be perfectly aligned with the upper

fwkwong

引用:

原帖由 fwkwong 於 25-8-2010 23:15 發表
Very easy !! This is a real steel, come with a very good Troy trench to tight up the special barrel nut.  The barrel nut looks similar to the original delta ring but with sharper teeth.  Then the rail ...

Here is the instruction

fwkwong

TRX 1.jpg.jpeg (128.94 KB)

TRX 1.jpg.jpeg (128.94 KB)
下載次數: 171

25-8-2010 23:19

引用:

原帖由 fwkwong 於 25-8-2010 23:17 發表



Here is the instruction

The instruction manual TRX 1.jpg.jpeg (128.94 KB)

TRX 1.jpg.jpeg (128.94 KB)
下載次數: 202

25-8-2010 23:17

[ 本帖最後由 fwkwong 於 25-8-2010 23:19 編輯 ]

fwkwong

引用:

原帖由 小劍仙 於 26-8-2010 00:04 發表

我會盡快架啦

Very good, go go go..... it is very light, well balanced, come with one 4 inch rail and two 2 inch rail.  I only install 2 short one, make it light and fast.  Perfect match with surefire X400.

fwkwong

引用:

原帖由 sailun412 於 26-8-2010 00:27 發表


started your toy work(s) yet?

yes, installing, perfect line up, show the picture later

fwkwong

!!

[ 本帖最後由 fwkwong 於 26-8-2010 02:25 編輯 ]

fwkwong

3 sets comparison....

1) 14.5 M4 PTW, KAC RAS setting
2) New upper, Noveske 12" from brother sailun412 , very good align with upper rail
3) prime GBB, Taiwan Madxxx Noveske 12" ...... not good , higher.....

Need some new stuffs to make this new PTW upper looks coooool !!!

fwkwong

引用:

原帖由 sailun412 於 26-8-2010 11:14 發表
wow!!! tremendous man! I'll try my best to arrange something for your new upper...

GOOD!!!  

fwkwong

FInally complete the new upper set

Sharing with all c-hings here

Welcome to all comments

Thanks to "sailun412"

[ 本帖最後由 fwkwong 於 2-9-2010 00:32 編輯 ]

fwkwong

Yes, M130 in RED cylinder, 9.6V battery, 6.01 PDI 374mm barrel, 0.20g BB

fwkwong

Yes, I shall try to fit it back to 3/4 cylinder.  Existing set of M130 in red cylinder did not give steady power. Difference of power between every shot ranges from 1.7J to 1.9J.  I don't know whether it was caused by replacing M150 to M130 spring for red cynlinder.

May be I will by a gold cynlinder set

fwkwong

引用:

原帖由 NCP013 於 2-9-2010 13:44 發表
隻FAG 可以再裝前D~

Let me try

fwkwong

引用:

原帖由 sailun412 於 4-9-2010 01:09 發表
another another one's upper again & again: 14.5" Afghan 6mm light carbin W/Switchblock.....

Very nice, I am waiting for the 9.5" open rail to suit the gas block  

fwkwong

引用:

原帖由 rmcevisu 於 5-9-2010 23:48 發表


扮mk18mod0  ^^
仲差枝kac grip..........

Tango Down grip is not bad, but make it black