發新話題
打印

G & P M4 RAS Kit (PackA)

引用:
原帖由 14692 於 6/22/07 00:57 發表
點解唔諗吓用已有既setting出到最大既效益呢?
well... I know what I am after... around 32-35 ROF and 360-400 ft/s...
in this case I need to use 1st Gear, 1st Piston, Xystema Motor, MOSFET, 1st 6.03mm Barrel, 10.4V battery... I will going to broke for a while...
Guns... lots of Guns...

TOP

回覆 #46 LifeAfterDeath 的帖子

cost effectiveness<----你明架?
本來無一物, 何處惹塵埃

TOP

引用:
原帖由 14692 於 6/22/07 01:04 發表
cost effectiveness<----你明架?
I know... but I don't mind to do that... I want to get the best for my C8... maybe in the future when I get more M4... I may do as what you do now... but for now... this one is for myself and for my CADPAT... I willing to spend alot more in this baby...
Guns... lots of Guns...

TOP

after more then 9 hrs of work... I finally work it out the basic of the C8...


but isn't over yet... still lots of stuffs need to work on...
Guns... lots of Guns...

TOP

回覆 #49 LifeAfterDeath 的帖子

好大條gap喎
本來無一物, 何處惹塵埃

TOP

引用:
原帖由 14692 於 6/22/07 09:12 發表
好大條gap喎
is still W.I.P. no where close to finish...
Guns... lots of Guns...

TOP

回覆 #51 LifeAfterDeath 的帖子

會唔會裝既步驟有問題?
本來無一物, 何處惹塵埃

TOP

引用:
原帖由 14692 於 6/22/07 09:57 發表
會唔會裝既步驟有問題?
I don't think so... I guess is the wire screwed up... cux I go from the front... not from the end...
Guns... lots of Guns...

TOP

回覆 #53 LifeAfterDeath 的帖子

條線頂起咗?
本來無一物, 何處惹塵埃

TOP

點會有gap? 等我又試下先
如果有gap, 條pin應該插唔入woo

[ 本帖最後由 steveyue 於 22-6-2007 14:11 編輯 ]
Saving Private Kai人

TOP

回覆 #55 steveyue 的帖子

會唔會套模已經開始走位
本來無一物, 何處惹塵埃

TOP

引用:
原帖由 14692 於 6/22/07 23:22 發表
會唔會套模已經開始走位
I better hope not...
Guns... lots of Guns...

TOP

回覆 #57 LifeAfterDeath 的帖子

好難講, 你咁大條GAP都落到前後PIN, 隨時係都唔奇
本來無一物, 何處惹塵埃

TOP

引用:
原帖由 14692 於 23-6-2007 04:57 發表
好難講, 你咁大條GAP都落到前後PIN, 隨時係都唔奇
縮水
一係D金屬料有問題.........
無理由QC都比佢出貨
Saving Private Kai人

TOP

引用:
原帖由 steveyue 於 23-6-2007 17:17 發表

縮水
一係D金屬料有問題.........
無理由QC都比佢出貨
qc 唔會拎D 金屬身去裝架喎....

TOP

發新話題