ayaka

引用:

原帖由 red_ant_tony 於 11-6-2009 22:00 發表
I'm currently using WOC original white nozzle set + Prime steel bolt carrier + a match O-ring from Reclamation street.

Your setting can use NPAS too.....search some old posts
there are some detail tutorial.....not so hard to modify~

belldanndy

師兄，請問你開始砌未？我都想跟住做。
咁樣係咪平過買支WOC再加Prime料？

引用:

原帖由 Castlevania 於 10-6-2009 21:41 發表
我宜家做左個LIST,將會緊住去做,希望C兄們指教一小弟.到時將會由零砌起,每步影相放上黎.
Prime Upper & Lower Receiver for WA-M4 - Colt (已訂)
Prime Lower Receiver Parts Kit for WAM4 (已訂)
Prime Steel ba ...

jpg

請問Castlevania兄, 係邊到訂呢? 咁多位師兄, 邊間舖有較齊prime 料呢. thanks.

Castlevania

引用:

原帖由 belldanndy 於 19-6-2009 12:30 發表
師兄，請問你開始砌未？我都想跟住做。
咁樣係咪平過買支WOC再加Prime料？

宜家仲未搵到我想要個隻款的16寸外管.....

[ 本帖最後由 Castlevania 於 19-6-2009 18:58 編輯 ]

Castlevania

[quote]原帖由 jpg 於 19-6-2009 18:44 發表
係西京,明搶啊~個D有primX買~

[ 本帖最後由 Castlevania 於 19-6-2009 20:05 編輯 ]

jabberwock624

引用:

原帖由 jpg 於 19-6-2009 18:44 發表
請問Castlevania兄, 係邊到訂呢? 咁多位師兄, 邊間舖有較齊prime 料呢. thanks.

係紅狐買0米得0羅!比較齊prime0既parts.
但價錢亦比較貴!

Castlevania

引用:

原帖由 belldanndy 於 19-6-2009 12:30 發表
師兄，請問你開始砌未？我都想跟住做。
咁樣係咪平過買支WOC再加Prime料？

等緊齊料先會開工,
宜家齊左6成料~

red_ant_tony

Thanks. I would like to ask whether the complete NPAS 'plastic' nozzle set is fragile or not? The 'white' GP nozzle is definitely durable.

ayaka

引用:

原帖由 red_ant_tony 於 20-6-2009 07:17 發表
Thanks. I would like to ask whether the complete NPAS 'plastic' nozzle set is fragile or not? The 'white' GP nozzle is definitely durable.

many chings had bad experience with that translucent plastic nozzle
i think white nozzle is the best.....i replace my RA metal nozzle with the white nozzle
more elastic & durable

jcahmaens

引用:

原帖由 ayaka 於 20-6-2009 10:54 發表

many chings had bad experience with that translucent plastic nozzle
i think white nozzle is the best.....i replace my RA metal nozzle with the white nozzle
more elastic & durable

Totally agree! I have changed it back to white nozzle too... with NPAS... this combination is much better!

Castlevania

點解PRIME個身同PRIME個掛機座合唔到GA??
唔通我裝錯左??
有C兄教路嗎?
THX

ayaka

引用:

原帖由 Castlevania 於 25-6-2009 22:19 發表
點解PRIME個身同PRIME個掛機座合唔到GA??
唔通我裝錯左??
有C兄教路嗎?
THX

有無試下揼下佢?

Castlevania

引用:

原帖由 ayaka 於 25-6-2009 22:22 發表

有無試下揼下佢?

??
冇啊....你地本身會唔會緊樣嫁?
THX~

ayaka

引用:

原帖由 Castlevania 於 25-6-2009 22:24 發表

??
冇啊....你地本身會唔會緊樣嫁?
THX~

我換gp身出現過咁ge情況...prime身就唔肯定

Castlevania

引用:

原帖由 ayaka 於 25-6-2009 22:35 發表

我換gp身出現過咁ge情況...prime身就唔肯定

問題已解決了~
原來係FIT的關係,要用膠hammer慢慢打入去~
多謝lhlui和ayaka  C兄們的教導~