發新話題
打印

有無人用過國產MAGPUL FMG-9

引用:
原帖由 McDull 於 9-8-2010 08:42 發表
尋日見到國內舖頭有所謂第2版,吒咁睇就好過第1版好多。

撞搥既位置改善左,彈弓同推杆都做返好,理論上要執既野比第1版少好多。

不過就算係第1版,執完之後一樣FING得FULL得
McDull CHing, how to 執第1版既撞搥位置? I tried using the KSC short mags, but what's happening is that since the position of fire pin is slightly off so that it can't strike the valve properly. When it strikes, all the gas in the magazine leaks.

TOP

回覆 16# 的帖子

係咪偏右上

TOP

話時話有無師兄枝g18c 粒單連發製因為blow back 移位而打唔倒 ? 開頭仲諗住係玩fpg 果陣fing 鬆左 , 點知係blow back 果度力震郁左 ......
塑膠戰隊

TOP

引用:
原帖由 McDull 於 10-8-2010 23:37 發表
係咪偏右上
YES...how did u fix yours?

TOP

引用:
原帖由 edison0918 於 11-8-2010 07:21 發表

YES...how did u fix yours?
幫你問過移殖18既個件蛋散,佢話最好既方法係將18本身後面個抽野成組搬過去。

咁會執少好多野

我自己個支係23F,到而家都仲有D小問題未解決到

TOP

引用:
原帖由 McDull 於 11-8-2010 09:51 發表


幫你問過移殖18既個件蛋散,佢話最好既方法係將18本身後面個抽野成組搬過去。

咁會執少好多野

我自己個支係23F,到而家都仲有D小問題未解決到
I did have the KSC's hammer set transferred onto the FPG already, but still having that magazine problem....when using short magazines (without the base plate), the gas leak problem occurs because of the fire pin is off but the slide can be locked in place when magazine is emptied. But when using long mags, it fires ok, but the slide can't be locked back when mag is emptied......so frustrating..

Now i want to explore how to modify the FPG's lower receiver to get the fire pin in the right place.... so wanna see whether you've done that or not....thnx

TOP

我打算用ksc g17 and 我所10隻都係短夾  , 買個國產fmg-9 .......................................

TOP

引用:
原帖由 jkidd 於 11-8-2010 11:44 發表
我打算用ksc g17 and 我所10隻都係短夾  , 買個國產fmg-9 .......................................
呢位用17既CHING,請問你隻短匣上左FPG專用既個塊PLATE之後,隻匣篤唔篤得實呢

TOP

引用:
原帖由 McDull 於 11-8-2010 14:32 發表


呢位用17既CHING,請問你隻短匣上左FPG專用既個塊PLATE之後,隻匣篤唔篤得實呢
No...the base plate that came with the FPG is too thick.

TOP

引用:
原帖由 edison0918 於 11-8-2010 15:05 發表


No...the base plate that came with the FPG is too thick.
咁整定佢要用長匣

而家長匣平丫,可以買多幾隻

TOP

引用:
原帖由 McDull 於 11-8-2010 16:18 發表


咁整定佢要用長匣

而家長匣平丫,可以買多幾隻
That's what I think too ....but with long mags, i still have to figure out how to solve the slide stop problem....the slide won't lock back when mag is emptied...not only that, Part No. 66 (the slide release which you push to make the slide recoils back) won't work with long mags....

TOP

回覆 26# 的帖子

CHING你原本條SLIDE有無做過D咩野。

聽我個槍佬講,呢套野一定要有個相對新淨既18 SLIDE先有得執

佢下身個兩條軌聽講做高左少少,要攝返低D先行得

TOP

引用:
原帖由 McDull 於 11-8-2010 17:00 發表
CHING你原本條SLIDE有無做過D咩野。

聽我個槍佬講,呢套野一定要有個相對新淨既18 SLIDE先有得執

佢下身個兩條軌聽講做高左少少,要攝返低D先行得
I did that already in order to make the slide works...so now the slide stop and release are what I have to work on....

TOP

引用:
原帖由 McDull 於 11-8-2010 14:32 發表


呢位用17既CHING,請問你隻短匣上左FPG專用既個塊PLATE之後,隻匣篤唔篤得實呢
我未買呀 , 而家上來問下先喇

TOP

國產都fing 得咩??
幾$?
,應

TOP

發新話題