jackypoon

如果唔FIT, 我估係安裝時做漏左D野

jpg

謎底已經解開, 經蓮姐既引導下, 原來自己做左個傻仔 ....
以為隻定管牙淨係可以用呢connect 個base 同d extension,
其實係可以放係任何一個個位, 只要將d extension 反轉裝...

而家搞到我好想要多set 銀色.....

sailun412

引用:

原帖由 jpg 於 18-12-2010 17:55 發表
謎底已經解開, 經蓮姐既引導下, 原來自己做左個傻仔 ....
以為隻定管牙淨係可以用呢connect 個base 同d extension,
其實係可以放係任何一個個位, 只要將d extension 反轉裝...

而家搞到我好想要多set 銀色. ...

哈哈...其實"反轉extension"呢個靈感來自係prxme個套¥19,000-(税別)既WA gbb駁管, 不過當然佢砌唔到甘多長度啦....
呵呵....銀色正丫 我自己用緊條prototype都係銀色...
早幾日幫個鬼仔砌又係銀色....

[ 本帖最後由 sailun412 於 19-12-2010 01:10 編輯 ]

payment

引用:

原帖由 sailun412 於 19-12-2010 00:39 發表


哈哈...其實"反轉extension"呢個靈感來自係prxme個套¥19,000-(税別)既WA gbb駁管, 不過當然佢砌唔到甘多長度啦....
呵呵....銀色正丫 我自己用緊條prototype都係銀色...
早幾日幫個鬼仔砌又係銀色....

咦…係咪七寸gas block?…

jpg

引用:

原帖由 sailun412 於 19-12-2010 00:39 發表


哈哈...其實"反轉extension"呢個靈感來自係prxme個套¥19,000-(税別)既WA gbb駁管, 不過當然佢砌唔到甘多長度啦....
呵呵....銀色正丫 我自己用緊條prototype都係銀色...
早幾日幫個鬼仔砌又係銀色....

呢個反轉extension concept真係ok!!

睇落去銀色仲做得靚過黑色, 黑色太黑, 唔夠真.

sailun412

引用:

原帖由 jpg 於 19-12-2010 14:02 發表


呢個反轉extension concept真係ok!!

睇落去銀色仲做得靚過黑色, 黑色太黑, 唔夠真.

最初想造隻色係淺色d架, 但係legal advised話黑d好 同好多人又嫌原裝太淺唔像真所以最終都係造黑d....

jackypoon

引用:

原帖由 sailun412 於 19-12-2010 00:39 發表


哈哈...其實"反轉extension"呢個靈感來自係prxme個套¥19,000-(税別)既WA gbb駁管, 不過當然佢砌唔到甘多長度啦....
呵呵....銀色正丫 我自己用緊條prototype都係銀色...
早幾日幫個鬼仔砌又係銀色....

蓮姐,我有野問. 請問隻GAS BLOCK跟唔跟PRXME數

sailun412

引用:

原帖由 jackypoon 於 19-12-2010 23:58 發表


蓮姐,我有野問. 請問隻GAS BLOCK跟唔跟PRXME數

一般22mm都fit!

payment

引用:

原帖由 jpg 於 19-12-2010 14:02 發表


呢個反轉extension concept真係ok!!

睇落去銀色仲做得靚過黑色, 黑色太黑, 唔夠真.

有一隻custom 既銀色仲靚…不過好似得一支………

fwkwong

Finally change all to Lipo battery

sailun412

哈哈...牙刷到呢 ....

red_ant_tony

引用:

原帖由 fwkwong 於 21-12-2010 00:01 發表
Finally change all to Lipo battery

Nice weapon!

I can see that you are using the original S-max buffer tube. Could you kindly tell me which CTR stock are you using? PTS or mil-spec?
Do you need to modify anything?

Also, which shorttened ECU are you using? The airsoft surgeon one?

Thanks.

fwkwong

引用:

原帖由 red_ant_tony 於 21-12-2010 07:27 發表


Nice weapon!

I can see that you are using the original S-max buffer tube. Could you kindly tell me which CTR stock are you using? PTS or mil-spec?
Do you need to modify anything?

Also, whic ...

I only used PTS CTR. Enlarge the internal of it a bit with a sand paper wheel. Also sand the corner of the tube a bit to make it smooth
I did not use any short ECU. Therefore the stock cannot be completely collapsed, with 1 slot remained but it is fine for my my habit to have 1 slot extended.

jackypoon

又消費....D 皮既mechanic設計真係冇得頂~
另外, 唔該晒妹仔幫佢診治把鵝公喉聲~~~



[ 本帖最後由 jackypoon 於 22-12-2010 00:40 編輯 ]