michaelredknapp

Hi, everybody,
i'm new in air soft world, can anyone tell where i can buy the sniper kit for PTW M4??
i went to kong wah st. today, n the sales there told me the king arms kit won't fit in my PTW, what should i do?? i really like that 24" sniper kit......
would someone help please??


[ 本帖最後由 michaelredknapp 於 3-8-2010 23:29 編輯 ]

ayaka

the handguard should fit the ptw receiver
but the barrel is only for the AEG......
and the longest barrel in the market is only 20"

michaelredknapp

Oh, is that mean the longest kit available is 20"??
and could you plz tell me where i can buy this???
thank you very very much.

ayaka

there should be no conversion kit specifically made for the ptw
normally aeg handguards can be installed onto ptw
but you need to buy a ptw outer barrel (longest one is 20")

you can find them in kong wah st.!

michaelredknapp

icic
thank you very much!
u r really helpful, may i ask my last question, as u know i want the 24" in the very beginning, in fact i want it even longer,
but now i know the longest barrel is 20", so i'm thinking if i can add a silencer to make it longer, n fit in a longer PDI inner
barrel, EG: 650mm @@.
do u think it will work??
if it will work, with the power supermax provided, the M4 should be come a very very strong sniper rifle, right???

i know this is a crazy idea, but i really wanna know if it can be work out.....
thank you for answering my stupid question....

Elf

mike, lawrence here
FORGET ABOUT YOUR 24" BIG DICK

michaelredknapp

NO!NO!NO!

i want it BIG, in fact i'm going to get 2 extra upper body, one is the giant monster of cuz,
another one is a 5inch mini dick head......HAHA  ^^
hope my idea can work out.......really looking forward to fight with it.

Elf

who's gonna 報位if u go sneaking like me and W?...

michaelredknapp

dun worry la,
i'll still play as i played,
the 5inch is for those (last enemies), when u guys dun need me to 報位......

Elf

you are our exclusive observatory mate
planning to get an extra cylinder set besides the supermax original one?

ayaka

引用:

原帖由 michaelredknapp 於 4-8-2010 01:22 發表


icic
thank you very much!
u r really helpful, may i ask my last question, as u know i want the 24" in the very beginning, in fact i want it even longer,
but now i know the longest barrel is 2 ...

PDI only have 20" inner barrel for the PTW
my PDI 6.01mm 14.5" barrel performce nice grouping and pretty long range~
so I think 20" barrel is already super!

michaelredknapp

yes, in need, no one will play with me if i use the original one with the 5 inch dick head, close range shot with sliver cylinder...............too dirty.
isn't it.

michaelredknapp

oh,
is 509mm the longest???

anything long than that won't fit ptw??................too bad....

Elf

the m4 ptw cylinder is 66 mm long x 6mm radius
volume of cylinder = πr^2*height - 7460mm^2

volume of a 509mm barrel = 509 mm long x 3.01 mm radius
volume = 14384mm^2

so basically there will be a suction from the cylinder when the cycle completes that draws air out of the barrel.
this is the same as i've told you. this will create a turbulence for the BB and it will definitely go curved

Elf

measurement of m4 cylinder is based on these factors :
1) M4 cylinder is a 3/4 cylinder instead of full cylinder of M16.
2) spring guide, spring and cylinder takes up considerable amount of space.
3) outer diameter of cylinder is 25.5mm, however the inner wall is about 5mm each side, making about 6-7mm radius.

however, considering a M4 363mm inner barrel has about 10k mm^2 volume, the above calculation is indeed too conservative.
I would say a M4 cylinder is roughly 11000mm^2 and that cannot feed a 509 mm barrel at all.